Sunday, March 16, 2008

Time to get precise...

Work is still keeping me busy (for about the next 2 weeks) then things should get much better.  In the meantime, as a mental exercise, I decide to come up with the basic math for gear rations and size.

In the past when working on the wooden versions of the clock, I did some basic math to make sure the gears would work.  However, the wood was much easier to correct if there was an issue.  It was really easy for me to redo a gear if I needed it.  With the metal gears, an awful lot of work goes into one of those gears.  I can't afford to fake it anymore.

The problem is that given a particular distance between two arbors (axles) and what ratio of movement was needed (for every turn of one gear, the other should turn six times), I came up with a fairly simple formula.

d = distance between arbors
r1 = radius of smaller gear
r2 = radius of larger gear
t = ratio between gears

This is what I came up with.
r1 = distance / (t + 1)
r2 = distance - r1

Anyone care to check me on this?  :)  My address is medievalsmith@gmail.com if you don't have a Xanga account.

I hope to get back to the forge soon.  When I do, I need to start being precise on my measurements, I am going to try to be very careful with this.  However, I also want to try and be precise using what they may have done in the middle ages.

I will use a divider to do the formula above.  For example, assuming a 6 inch distance and a need for ratio of 10 to 1, I will take the divider and attempt to divide the distance 11 times (remember the formula up above, ratio plus 1...).  The measurement of one division would be equal to the distance on the divider.  That will also be the radius of my smaller gear.  The other radius would be 10 of those divider distances.  It may sound complicated but it really is not that bad.  I wanted to come up with a simple technique that would not require the use of a ruler marked to very fine degrees.

Another nice thing about doing it this way is that what few examples I have seen of medieval clockmakers, they always have dividers but I've never seen one depicted with a ruler.

NOTE: When I refer to a radius up above, it is the distance if the gears were simple wheels with their outer edge touching.  For actually gear teeth I will have to add a bit to the size listed above to allow tooth contact.  In most cases that will a little under 1/4" added to both gears.

Another thing is that up until now when I have been working on the clock I have often been experimenting.  This means that I often rushed parts especially if I was doing it during a public demo.  From here on out, I am going to try and adopt the attitude of making the final part.  I don't want to have to redo many more parts...

Tuesday, March 4, 2008

Just a bit of an update.

  This past weekend I worked at a festival near Jacksonville.  I spent the entire day doing blacksmithing for the public.  I am surprising myself with my speed at producing half way decent looking items.

  Work is really keeping me busy.  :(  However, I am going to try to make time this weekend to get some time in on the clock.  I noticed a problem with the clock that I will show details of later.  Not a big issue (and to be honest, I'm glad that it happened) because I wanted to remake the one part anyway.

Sunday, February 17, 2008

A bit of a helpful video.

  Found this on Youtube.  It is of the Salisbury cathedral clock.  Although it predates the clock I am working on, all the parts are basically the same.  At about the 30 second mark is some good video of the verge and foliot rotating as well as the crown wheel.

http://www.youtube.com/watch?v=5UKlVaGwJ78

More progress...

  Managed to spend more time on the forge today and made some decent progress.  Mainly I was working on the arbor for crown wheel.  Not really anything special about it.  The process was very similar to working on the arbor for the great wheel.  The arbor is mostly formed.  It just needs a bit of touching up.  I will post some pictures of it later.

Saturday, February 16, 2008

Progress...

I am attempting to drive to getting the clock to actually ticking so I continued work on the escapement assembly.  Today I made two simple pieces.  The first was an "L" shape at the bottom of the verge and foliot.  This piece has two purposes.  The first is to hold the verge and foliot in place as it comes in contact with the crown wheel.  It is also a bit of a safety feature.  If the wire holding the verge and foliot breaks, this piece helps to keep it from falling through the clock.  It was a pretty simple piece and these pictures show it being made.

EscapementBottom1

EscapementBottom2

This final picture shows it riveted to the frame.  I have the verge and foliot resting in it.

EscapementBottom3

  The next piece is mildly more complicated.  It is a "U" shaped piece of metal.  It is designed to hold one end of the crown wheel arbor.  Because of the placement of the verge and foliot, the end of the crown wheel arbor cannot hook into the frame.  This piece is designed to wrap around the verge and foliot and provide the arbor with someplace to rest.

  I started by rounding the end of a piece of metal.

CrownArborSupport1

The center part is then thinned out.

CrownArborSupport2

After some more thinning, a hole is punched and drifted to form the hole where the arbor will connect.

CrownArborSupport3

The other end is spread out and I punch two holes for rivets.

CrownArborSupport4

I give it the "U" shape.

CrownArborSupport5

The piece is riveted to the frame.  I used the old arbor from the great wheel to show how it works.  Notice that the end of the arbor goes into the piece rather than the frame.  This allows the verge and foliot to be in its proper positiong.

CrownArborSupport6

Sunday, February 10, 2008

Perhaps I need to make a marking tool...

  So far, with all of my blacksmithing, I have yet to make a touchmark.  None of the pieces I've made have an identifying mark.  I just came across this article.  http://www.yorkpress.co.uk/news/yorknews/display.var.1280776.0.turning_back_time_to_york_1300.php

It's a nice design.  I could see doing something similar but different enough to not be a copy.  Now, if I only knew someone that knows how to make things like this...  :)

 

The best laid plans...

  Well, I had set aside the entire weekend to work on the clock.  Unfortunately I got the flu on Friday.  I probably picked it up on the airplane.  Anyway, the fever did not break until Sunday evening.  Oh well...  Here's hoping for next weekend.  I am really, really anxious to get back to the clock.  If I can get the crown wheel done soon, the clock could be ticking within a few weeks.